Thanks.
I will try this configuration.
I'm using Redhat 3.0 ES.
I will post here my results.
Thanks again.
"Cameron Kerr" <cameron.kerr@paradise.net.nz> escribió en el mensaje
news:4005da93@news.orcon.net.nz...
> Rafa <rafa@este.correo.no.vale> wrote:
> > Hi, I need your appreciate Help.
> >
> > I have one linux box with 3.0 redhat and 3 network cards:
>
> You mean to say you have a Redhat _3.0_ box? That's _very_ old. Perhaps
> you mean 8.0 or 9.0?
>
> > eth0=10.0.0.1/24 ---- connected to private LAN
> > eth1=192.168.10.1/24 ---- connected to router DSL1 (IP
> > 192.168.10.2/24)
> > eth2=192.168.20.1/24 ---- connected to router DSL2 (IP
> > 192.128.20.2/24)
> >
> >
> > I want the following:
> >
> > Range between 10.0.0.10 to 10.0.0.127 connect to Internet using DSL1
mask
> > =/24
>
> Hmmm, this ones not very well designed (.10 is not a round number for
> this purpose) I would suggest changing it the lower end of the range
> from .10 to .15 (one less than 16), or higher (.31, .47, .63)
>
> If we change it to .16, we can allocate it like this, but note that it
> will be larger than the range. You can put in a more specific route
> entry to get the rang 10.0.0.0-15 pointing in the correct direction.
>
> route add -net 10.0.0.0/25 gw 192.168.10.2
>
> #This one fixes 10.0.0.0-15.
> route add -net 10.0.0.0/28
>
> $ ipsc -h 10.0.0.0/28
> IP address: 10.0.0.0
> Hexadecimal IP address: A000000
> Address allocation range: 10.0.0.0 - 10.0.0.15
> Full subnet mask: 255.255.255.240
> Subnet mask: 0.255.255.240
> Subnet ID: 0.0.0.0
> Network ID: 10.0.0.0
> Host ID: 0.0.0.0
>
> route add -net 10.0.0.0/28 dev eth0
>
> Because this route entry is more specific, it will be used in favour of
> the other ones
>
> > Range between 10.0.0.128 to 10.0.0.254 connect to Internet using DSL2.
> > mask=/24
>
> You can represent that as a single block of 10.0.0.1/25 (note the mask)
>
> $ ipsc -h 10.0.0.128/25
> IP address: 10.0.0.128
> Hexadecimal IP address: A000080
> Address allocation range: 10.0.0.128 - 10.0.0.255
> Full subnet mask: 255.255.255.128
> Subnet mask: 0.255.255.128
> Subnet ID: 0.0.0.128
> Network ID: 10.0.0.0
> Host ID: 0.0.0.128
>
> So you could use
>
> route add -net 10.0.0.128/25 gw 192.128.20.2
>
> > ?using iptables and iproute2?
>
> I don't (yet) know iproute2 syntax, but you should be able to translate
> what I have shown without too much trouble.
>
> > Thank you very much.
>
> Your welcome, but know that I haven't tested this.
>
> PS. You are aware that 10.0.0.0 is custamarily a class A network, right?
>
> --
> Cameron Kerr
> cameron.kerr@paradise.net.nz : http://nzgeeks.org/cameron/
> Empowered by Perl!